Accidentally snagged on your favorite leather jacket? Or did your dog's too sharp claws leave a through hole in it? Don't worry - we'll fix it. It can still be repaired, and besides, it can be handled on its own and without serious expenses.

To do this, you will need to find a wide, flat and well-lit surface (for example, a dining table) and some items:

  • transparent tape;
  • sharp knife;
  • toothpick;
  • small piece fabrics;
  • skin paint;
  • elastic adhesive on water based which does not leave stains (super glues will not work);
  • needle with thread.

Step 1.
Using your fingers and a toothpick, align the edges of the tear with each other and secure them with adhesive tape. Before using the tape, first glue it on your arm so that later there are no unwanted marks on the leather jacket, and then on the tear on the skin.

Step 2
Turn the jacket inside out through the seam where the sleeves are sewn on. If you do not see the factory seam, then you can use a knife, with which you need to make a neat cut. The incision should be large enough to reach from the inside the place that we are repairing.

Step 3
Apply glue to a small piece of fabric and press it against the inside of the hole where a thin layer of glue has already been applied. Press firmly. When the glue sets, you can turn the jacket back.

Step 4
Remove the tape carefully. Squeeze a drop of glue onto cardboard or any other surface. Slightly pull the edges of the hole and use a toothpick to apply glue between them. Blot the remaining adhesive with a cloth and leave to dry.

Step 5
Sew up the seam of the lining that you ripped open earlier.

Step 6

Paint the defect with a special paint for the skin.

Hints and Warnings:

  • During work, try to concentrate as much as possible so as not to cause more damage to the jacket.
  • This is how leather jackets are repaired in most workshops because it is one of the easiest ways.
  • Re-read the instructions several times so as not to be distracted during work.
  • If you have started the repair process, then you definitely need to bring the matter to the end. If the glue dries before you complete all the requirements, all efforts will go down the drain. Repeated application of glue is fraught with damage to the appearance of the jacket.
  • Most leather jackets are now dyed with special films, so make sure the adhesive tape sticks to the leather, which is not visible.
  • This method is only suitable if your leather jacket minor damage. Otherwise, it will most likely be necessary to apply a patch of leather of the same color, or another suitable one.

Here's a simple way you can try to "reanimate" your favorite leather jacket.

In search of warm clothes, ancient people created products from leather and fur. For many centuries, these materials have been used by mankind. Today shoes, jackets, bags, gloves are made of leather. These products are always in demand. After all, leather clothing is always in fashion. It is quite difficult to find a person who would not have a thing made from this material. It is worth noting that leather products are well preserved even after several years. Of course, during wearing, the material will gradually begin to fray, crack and age. However, do not rush to throw away such a thing. Today, there are means and all kinds of methods, thanks to which the repair of fur and leather goods became possible at home.

How to change the lock in a leather jacket

Repairing leather products is actually quite simple. Quite often the lock breaks in jackets. It is not always possible to fix it at home, as this requires special equipment. In addition, you first need to flog and then wedge in a new one. An ordinary sewing machine will not take leather. Therefore, you can simply sew a new lock on top of the old one. It is very fast and much easier than replacement.

A broken seam is not a problem.

Another problem that can occur when wearing a leather jacket is a broken seam. They can become unusable on the sleeve, on the side or on the back. In any case, the thing loses its appeal. Repair of leather products in this case comes down to just a few simple operations. To begin with, you should unpick the seam of the lining, which is just located in the area of ​​\u200b\u200bthe damaged outer seam. Now part of the jacket needs to be pulled out through the hole formed. A damaged seam can be sewn on a typewriter. If there is no such equipment, then you can do it manually by performing a small machine seam. After that, the stitched fabric can be returned to its place.

How to get rid of worn skin

Worn skin completely spoils appearance any thing. Some products begin to wear out around the third year of wear. At the same time, all qualities are preserved. Even if you have purchased a very expensive and branded item, scuffs will still appear. Restoration and repair of leather products in this case is reduced to painting. At the moment, a lot of special tools have been created that allow you to restore almost any thing. Paint comes first liquid skin. Of course, after using them, you can not leave products without proper care. Paint can be applied to any object with a regular sponge.

If the product has a shallow scratch, then it can be removed precisely on the metal. You can paint shoes with spray paint. It is worth noting that such funds can be purchased at almost any specialized store. A can of paint can even be used to paint jackets and handbags.

What to do with holes?

First of all, holes on leather products usually appear as a result of inaccurate wear. After all, the material itself is quite strong, so it is very difficult to tear it. If the hole is small, then leather goods can be repaired with your own hands, without the help of atelier employees. To begin with, the thing needs to be laid out on a flat surface and carefully straighten exactly the place where the gap occurred. To ensure that the edges of each piece are even, all protruding threads should be removed. Now you need to cut out. In size, this piece of matter should be slightly larger than the torn off one. Using tweezers, push the prepared fabric inside, and then gently straighten inside. This piece will serve as a patch. Now you can apply a small amount of glue to the fabric and glue a piece of leather. That's all. It remains only to remove all excess glue and clean the edges of the glued piece of leather. You can do this with a normal damp sponge. The skin should adhere after 8 minutes. After that, you can dry the patch with a regular hair dryer. If the glued piece is very different, then it can be slightly tinted. It is worth noting that after a careful repair, the leather patch is practically invisible.

Repair of leather products with liquid leather

Any material can be easily damaged. The leather product can be cut, scratched and simply torn. Alas, it is not always possible to restore things from this material perfectly. In most cases, the patched area remains visible. However, not so long ago, a new polymer appeared that allows you to repair leather products without obvious traces. Restoration of things with this tool can be done very quickly and at home. Liquid skin can be selected not only by color, but also by texture.

If it is impossible to find the perfect shade, then you can mix several tones. To compare the resulting color with the real one, you need to apply a little product on a small area of ​​\u200b\u200bthe product.

Such tools are best used to treat only damaged areas of the product. The special composition after application forms an elastic and durable layer. In color and structure, it resembles natural leather. If the damage was serious, then you need to apply the product in two, or even three layers. It is worth noting that liquid leather well masks traces of tears after gluing individual pieces, knocked down toes on shoes, as well as all kinds of chips and scratches on products. The tool is considered the most effective. However, such a product can only be used for the restoration of smooth leather products.

There are also precautions. It is necessary to work with liquid skin only in polyethylene gloves. The use of rubber products is prohibited. Finding plastic gloves is not so difficult. They are often used in hair coloring.

How to use liquid skin

Restoration and repair of leather products will be much faster if you use liquid leather. Before applying the product, the surface must be cleaned of any kind of contaminants. This will give you the best result. For application, you can use a sponge or a regular art brush.

It is worth considering that liquid skin begins to dry out only after 30 minutes, and to polymerize - for several hours. Finally, the remedy will be strengthened only a day after use.

Liquid skin should be applied evenly and in a very thin layer. For leveling, it is better to use a regular dry sponge. In this case, it is worth pressing it a little to the surface of the leather product. This will create the necessary relief. Let the product dry.

If necessary, the procedure should be repeated. This may be required when restoring small cracks, small cuts and abrasions. As you can see, repairing and painting leather products takes very little time.

Best Liquid Skin

At the moment, liquid skin is produced by many manufacturers. However, the most better remedy for the repair of leather products - Saphir. This liquid skin has passed many tests and is a high quality product. This tool is made in France. The original name is Saphir Creme Renovatrice skin restorer. A similar product can be used to repair the front layer of jackets, shoes, handbags and other things. Usually it is used for the restoration of products from all types

Leather is a versatile material that allows you to create various products, from shoes, things and outerwear to interesting decor. However, although it is quite wear-resistant, it requires constant care and, in case of damage, restoration.

Absolutely any material has the ability to wear out. Even high-quality leather can get damaged over time. It depends on the availability of care for the product, and on the duration of wear. The leather jacket is particularly susceptible to damage as it is an outerwear item. Most often, the collar and cuffs with pockets are subject to restoration - since it is these parts of the leather jacket that are subjected to more friction.

You can repair a leather product by contacting a professional studio, but their services are usually quite expensive. Do not be upset - with minimal damage, you can handle it yourself.

Thankfully, in modern world there are many various materials and ways to apply them at home and help extend the life of your leather product.

Types of damage

Deciding how to restore a leather jacket can only be determined by how exactly the damage was received.

The main types of damage that can be repaired at home:

  • breaks. An accidental hold on a nail or any other sharp object can ruin the look of a thing.
  • Scratches. Contact with third-party things, accidental scratches in public transport- all this makes the appearance of a leather jacket unsightly.
  • Scuffs. Most often formed from constant friction with a bag or backpack, as well as in places that most often come into contact with other surfaces: for example, sleeves.
  • Color fade. Externally, the jacket may not have any visible damage, however, over time, it may lose its original color in places exposed to light and external factors.

Therefore, in order for the jacket to serve for a long time, you should pay attention to its care and clean the skin in time, as well as use special means to maintain her condition.

Jacket repair

You can repair a leather jacket yourself if you are not afraid to damage the product even more. It is best to get time for work and a comfortable workplace. It is very important to take into account the availability of materials that are needed for the restoration and acquire them in advance.

The main materials that may be needed and depend on the type of damage:

  • Skin glue.
  • Degreaser.
  • Tassel.
  • Color matching threads.
  • Needle.
  • Skin paint.
  • Patch materials.

Materials should be used depending on the situation, but it is better to prepare them in advance. It is very important to act carefully and do quality work - so there is a chance that the restoration will be successful and the jacket will last for a long period of time.

Elimination of tears, cuts

Damage such as tears is perhaps one of the most unpleasant moments that can upset any owner of a leather jacket. Most often it happens that the skin is torn either completely or in a corner.

To get rid of the gap it is best to turn the product on wrong side, rip open the lining and find the cut. This area must be wiped with a special solution in order to degrease the skin.

Next, you should choose a piece of leather of the same color as the material of the jacket. Lubricate the area around the gap and the cut patch with glue. Fold the tear on the leather jacket as close as possible and apply glue again. Then glue the patch to the gap.

Important! The patch should be taken in such a size that it is a couple of centimeters larger than the tear on the jacket.

After carrying out such a recovery procedure, you need to put the glued area under the press for at least a day. Then it remains only to sew up the lining and wipe the gap on the outside of the product to get rid of traces of glue.

How to fix a hole in a leather jacket

Sometimes it happens that any damage may not be noticed immediately. One of the most unpleasant are holes, which can damage the product very much, as they tend to spread over larger areas.

The main thing is that if damage is detected, immediately seal it with a plaster to avoid final damage to the appearance of the jacket.

Ways to fix the hole:

In cases of large-scale skin tears in the jacket, it is better not to make independent attempts to restore the jacket, but to turn to professionals.

Elimination of abrasions, repair of the collar

Scuff marks are not a huge problem for leather jacket owners if you know how to deal with them. You can get rid of such problem areas on the product with the help of cream, glycerin, paint or other aids:

You can renew your collar with baking soda. To do this, you need to apply a small amount of it on a soft sponge and gently rub the greasy place. Similarly, you can apply glycerin or paint.

Important! It should be remembered that correct selection paint colors are the key to success for the restoration of the product.

How to restore/refresh a jacket at home

Sometimes, of course, the question arises of simply updating the color of a leather jacket, and for this, you first need to choose a product that is suitable for leather items.

The easiest way to refresh the product is with the help of spray paint, which is sold in specialty stores. Before starting work, you need to clean the jacket from dust and dirt, and only then start work.

A leather jacket should be hung on wide, comfortable hangers so that the material does not form wrinkles and can be applied evenly. The paint should be sprayed at a distance of approximately 20 centimeters from the product at a fairly fast pace.


After full staining, the jacket should be left in this position until the paint is completely dry. If after that there are places where the paint has taken worse, you can process the product again.

Prevention, leather jacket care

To keep your leather jacket in good condition special care products should be used that not only clean the skin, but also help restore the material, add shine to the material and carry out minimal disinfection.

Among these funds are:

  • Spray that repels water. It can help keep the original look of the product.
  • Wax. Its use helps to make the material soft, which is an excellent prevention of cracking, especially in the cold season.
  • Sponge for cleaning. The special material does not damage the skin and cleans the product as delicately as possible.
  • Foam cleaner. Gives extra shine, helps to get rid of dirt.

These tools are quite easy to use, but make it easy to extend the life of the leather product.

We hope that the tips presented in this article will help you keep the look of your leather jacket in its original form for much longer.

Absolutely anything can break. Often people encounter such a problem as the formation of a hole in a leather jacket.

Repairing a leather jacket is a painstaking job. If the material is torn apart, then the person is required to have a minimum experience in owning sewing tools. When these skills are absent, it is better to abandon such an undertaking, since you can only make things worse.

What methods of gluing leather items exist and what is required to complete the job?

Methods for repairing leather products

At the present time, there is a huge selection of materials for gluing surfaces.

To glue the product imperceptibly, the glue must have a number of characteristics, these include:

  • elasticity;
  • good viscosity;
  • fast drying;
  • heat resistance;
  • resistance to water, fats and oils.

Most of all, under these characteristics, the universal glue "Moment" is suitable. In some situations, you can use rubber glue, which is used to repair shoes.

Other materials are used much less frequently: PVA, nairite glue, liquid skin.

What to choose, you need to decide for yourself. But before performing the procedure, you must read the instructions.

The use of glue "Moment"

Often there is such a situation when a piece of material comes off on the outerwear and a hole is formed. It is possible to correct the situation.

How to seal a leather jacket at home?


To repair things you will need:

  • glue "Moment", which is used for gluing shoes. They call it rubber. It is considered elastic, so it will fit well on the skin;
  • a piece of leather or suede. They can be taken from an old and unnecessary glove;
  • scissors;
  • tassel;
  • several pieces of toothpicks;
  • solvent. It will help to degrease the glued plane;
  • paint for leather products;
  • hammer.

You can sew a jacket with glue according to the following scheme:

  1. First you need to take a patch and fix it on the wrong side of the jacket, providing an approach to the torn part.
  2. It is better to find a place in the lining where you can tear the fabric and get to the damage.
  3. Take an old glove. A small piece is cut out of it and glued to the inside of the damage. We glue the patch, but in order for it to be well fixed, it is necessary to put a heavy object on it, for example, a hammer. It is worth noting that a piece of skin can be any color, as it will not be visible anyway.
  4. Once the patch dries, you can do the front side. Here it is necessary to select suitable shade shred. It is cut out exactly the same shape as the hole itself. The edges must completely converge with each other. To match them, glue is used for alignment.
  5. Once everything is glued, the patch needs to be tinted. This will help make it less noticeable. For such purposes, paint for leather products is used.
  6. The final step is sewing up the lining. The fabric must be sewn with the same threads that were used when making the stitches.

Repairing a cut on a jacket in this way will be difficult for a beginner. Therefore, it is better to choose an easier method.


Repairing a cut on a jacket

A cut on a leather jacket very often appears after a hook on a nail. Many believe that after such an incident, clothes can no longer be repaired.

But how do you fix a hole in a leather jacket? Everything can be fixed with gluing.

If the thing is torn, then the following recommendations should be followed:

  1. At first outerwear turned inside out from leather. Then the lining fabric is carefully examined. This is necessary in order to find the place where the seam was broken.
  2. After identifying it, you need to cut the stitches, and use your hand to find a cut.
  3. Now we need to prepare the patch. To keep it well, the rupture area must be degreased with a solvent.
  4. A piece of leather or suede is selected. Its size should be several centimeters larger than the cut itself.
  5. On the inside, glue the edges with glue. The same composition must be applied to the patch.
  6. The glue should dry a little. This will take about 10-20 minutes.
  7. This procedure can be repeated again.
  8. As soon as the glue dries, the flap is applied to the torn surface. In order for it to be well fixed, it is necessary to press and put a heavy object.
  9. After two or three minutes, the jacket is turned inside out. front side. The cut edges must be pulled closer to each other. A toothpick lubricated with glue will help with this.
  10. Once everything is dry, paint can be applied.
  11. The final step is the careful stitching of the lining.

Don't worry about the hole reappearing. If you use this repair method, then the jacket will no longer tear in this place.


Application of liquid skin

This method is good when there are small cracks on the jacket.

How to glue a leather jacket with your own hands using liquid leather? Do-it-yourself leather jacket repair is done with a bandage and a small spatula.

The second item can be easily made from an old bank card. A strip about one or two centimeters wide is cut out, and then the end is slightly pointed.

The following diagram will help glue the hole:

  1. A small piece is made from the bandage. It should be slightly larger than torn fabrics.
  2. On the front side with a homemade spatula, apply liquid skin. A piece of bandage is placed on top and adheres well.
  3. The area to be glued must dry. This will take about 7-10 minutes. The procedure is repeated again. Only liquid skin is applied to the bandage flap.
  4. The repaired item must dry completely. This will take two to four hours.

This method allows you to repair a leather jacket yourself. But the problem may arise in the acquisition of liquid skin. The material is not sold in all sewing stores.


Leatherette repair

At the present time, manufacturers offer a wide range of jackets that are made of leatherette. They are no worse than leather, but much cheaper.

But how to fix such a thing? You can repair it in exactly the same way.

It is worth noting that not any glue is suitable for repairing such products. If you close the hole with "Super Glue", then this can lead to damage. What to do then? We remove the glued place and repair the jacket in a safer way.

Non-woven tape will help remove damage. This material is very thin, so it will lie unnoticed.

The procedure must be carried out according to the following scheme:

  1. Locate the hole on the wrong side. Open the lining along the seam and make free access to the damage.
  2. Glue the non-woven tape to the inside. Place gauze on top. Walk with a hot iron.
  3. When the material sticks, the gauze can be removed.
  4. Sew up the lining on the inside with a neat seam.

This method is considered easy and simple. The tape, when exposed to steam, is firmly attached to the surface. Thus, an imperceptible patch will be obtained.

If a person does not know how to sew a jacket, then you can watch training videos. As soon as you repair a thing, you need to let it dry for two to three hours. When gluing, it is worth considering all the recommendations experienced housewives.

Products made from natural materials are valued for their beauty and consumer qualities. The leather jacket is no exception. However, you need to know how to take care of it, and in case of loss of integrity, return it to its previous appearance. Of course, removing a hole in the skin is not the easiest way to restore, but sometimes you can’t do without it. There is only one thing left - to glue it. At home, a leather jacket, like any other product, can be easily repaired by yourself. To do this, you need a pair of hands, a little imagination, patience and free time.

In our age, gluing any two surfaces is not a problem. Therefore, at home, like suede or leatherette, using glue is also possible. Moment, waterproof PVA or nairite are often used as adhesives. All of them have properties without which repair would be impossible:

  • quick drying of the layer;
  • plastic;
  • resistance to high and low temperatures;
  • viscosity;
  • resistance to fats and water.

In order to connect leather surfaces, glue from Henkel is most often used. The famous "Moment" can be found in almost any store, but you need to choose the one that says "universal" or "for shoes" on the tube.

The second most popular is waterproof PVA glue. In addition, viscous nairite glue perfectly grasps the surface, and liquid skin allows you to work with the layer for as much as twenty minutes.

When is Moment useful?

You can repair a leather jacket if it is torn. Restoration of a lost skin fragment is effectively carried out using "Moment" for shoes - rubber glue. It has excellent plasticity, and during the operation of the product, the adhesive layer will naturally stretch and shrink along with the base. It's also good to stock up on:

  • Solvent. Needed for degreasing treated surfaces.
  • Leather or suede patch.
  • Small sticks (matches), toothpicks.
  • With a brush.
  • Skin paint.
  • Scissors.
  • Small weight or hammer.

The restoration process itself is quite simple. However, it requires some order to be followed. What should you do if your leather jacket is torn?

Working with liquid skin

It is very convenient to work with this material, because it is an alcohol-based polymer substance. The structure is somewhat similar to glue. However, it should be used carefully so that the products are neat.

Under certain conditions in the work, the polymer layer is completely connected to the restored surface and becomes indistinguishable from it.

The polymeric mass can also be conveniently used if the damage to the leather layer is insignificant, for example, in the event of a cut. To eliminate it, the following materials are needed:

  • Small spatula. It should be no more than 1 cm 2 in area. You can make it from an old credit card or a plastic bottle.
  • Medical bandage. You will need a small piece of it.
  • Jars with liquid skin. If the product being restored has a complex shade, it is possible to mix several colors of the polymer.

A small part is cut off from the bandage, corresponding to the size of the cut. Using a spatula, a little liquid skin is applied to the surface of the jacket. It is worth noting that the polymer should be smeared exactly along the damaged edges. This should be done carefully, the excess can be removed with a regular sponge for washing dishes.

Then the glued and dried bandage is completely covered with a thin layer of polymer. After drying, the resulting surface will be almost indistinguishable from the outer layer of the jacket. The time for complete drying of the layer is approximately three hours.

There is another method to eliminate the cut. However, it can also be used in the case when a hole has already formed on the product. To do this, you will have to use a leather or suede patch. It is glued on the inside of the jacket, spreading the lining in the right place. Then, a layer of liquid skin is applied to the pasted flap from the wrong side. Let it dry completely and then apply another one. As a result, the scratch will be completely eliminated.

Leatherette repair

Along with products from genuine leather, similar leatherette products are widely represented on the market. but artificial leather does not differ in durability and can crack over time, and even simply tear. Repairing it is as easy as patching a hole in a leather jacket. The only difference is that the usual rubber “Moment”, and any other glue, is indispensable here. It can damage the fragile surface of the material and lead the product to an even more deplorable state.

Therefore, as an alternative to glue for leatherette products, it is customary to use non-woven tape, which adheres to the layer under the influence of heat. To repair a hole, crack or scratch, you will need an iron and the following materials:

  • non-woven tape;
  • liquid skin;
  • shred cotton fabric or a regular medical bandage.

The lining material of the jacket is ripped in the right place along the seam. Having gained access to the wrong layer of leatherette, a non-woven patch is applied to it, and a layer of fabric is added on top. The fabric is ironed with a hot iron along with non-woven fabric, which from this is connected to the leatherette base. On the front side of the jacket, the patch must be patched with liquid leather in two layers. Each such layer must dry separately.

How to sew a jacket

With your own hands, a leather product can be repaired not only with the help of adhesives, but also with the help of a thread with a needle. This method is suitable for those people who can and know how to work with a sewing machine. So, for work you will need:

  • glue;
  • leather and fabric shreds;
  • skin needle;
  • threads to match the jacket.


If the jacket is torn through and through, then in order to prevent the edges of the hole from spreading even more during its operation, you need to glue a piece of plaster on the wrong side. It will hold the edges together and keep them from fraying.

Then, if the damage is significant and it is impractical to use a combination of glue with liquid skin for repair, you need to get sewing machine, prepare a leather patch to match the jacket.

The skin flap should be similar in shape to the area of ​​the tear, but be slightly larger. The patch is sewn on a typewriter directly on the front side of the product or from the inside. In the first case, it is recommended to use a "zigzag" seam, and in the second - a "line".

In some situations, it is worth "beating" the patch so that it becomes a kind of decoration for the product. To enhance this effect, you can cut another hole in the skin and sew it up in the same way as the first hole.

Read about how to put a patch on a bologna jacket
Read about how to put a patch on a bologna jacket