In most cases, the interior door handle comes with the door itself, and the choice is limited to the range of fittings that the manufacturer uses. But even in this case, you need to know what they are. And even more so this knowledge is necessary when replacing the door handle.

Overhead handles for hinged wooden interior doors

The easiest to install are the so-called handle-brackets, holding on to which you can open or close the door. The main function is to provide the opportunity to pull the door towards you (to push it away from you, the handle, in principle, is not needed). But the simplicity of the functionality does not mean the limitations of forms and style solutions.

Here are examples of "Soviet constructivism" - nothing superfluous and a complete lack of decor:

And since such pens are still in demand, its only difference from that era, and to some extent “decoration”, is the coating with modern hammer paint. They fasten such a handle directly to the canvas with four screws, and put it mainly on inexpensive paneled doors.

Modern models are much more attractive in form and decor. For example, such an Art Nouveau handle will serve as a real decoration for an interior door:

Even a simple rectangular "bracket" can be made attractive by adding an engraving to the bracket itself and attaching it to a trim strip. Like this classic style pen:

There are also overhead handles with a hidden fastening, which, even for a simple form, will only improve its decorative qualities. They are fastened in pairs, opposite each other, on two studs, for which through holes are drilled in the door leaf.

The only drawback of the overhead handle is the lack of a latch. This may affect if the door frame has lost its vertical. Moreover, such a loss does not necessarily occur due to poor-quality installation of the box - any house is subject to shrinkage and sediment (and wooden ones also shrink). And so that the door does not spontaneously open (or close), clamps are added to the overhead handles, which consist of two parts. The main part of the mechanism with a roller or ball is cut into the end of the canvas, and the counterpart is into the box.

Lever handles for wooden swing doors

Most interior door handles have a movable handle that actuates the latch. That is, with the help of a handle, the door is not only opened or closed, but also fixed in the door frame.

The simplest push model with a conventional latch assembled looks like this:

In addition, such a handle can also have a lock function. The locking mechanism can be actuated in two ways - either from inside the room using a rotary knob:

or outside with a key.

And although the larva is arranged on the principle of a disk lock, its degree of secrecy is minimal. And the lock itself does not protect against breaking the door, but simply provides protection for the personal space of the owner of the room.

"Responsibility" for aesthetic properties, like the previous type, falls mainly on the handle: metal, wood, glass, porcelain ... There are even with rhinestones.

Such handles also have differences in the form of a decorative lining. In addition to the round rosette, as in previous models, they can be equipped with oblong-shaped overlays.

Moreover, this form of lining allows you to hide two holes in the door under it: the upper one for the latch drive handle, the lower one for the handle and the lock cylinder.

Knobs for wooden doors

The word "knob" comes from England. A narrow translation of a noun is a pen, a bump, a head. But there is also a “technical” translation - a round doorknob.

The simplest knob without a latch mechanism can be considered a classic interior door. Similar handles made of wood or plastic were also produced by the Soviet industry.

Now most of these models are equipped with a movable head and a latch. And they belong to the rotary type.

Like push knobs, round rotary knobs can have a simple latch.

But if they have a handle on the inside for fixing the latch, then on the outside they are equipped with either a key cylinder or a screw for a flat-head screwdriver to force the latch to unlock.

Sliding door handles

If the sliding door moves parallel to the wall, then overhead handles are also suitable for it. This is exactly what full glass sliding doors are equipped with.

But wooden models, regardless of whether they “hide” in a cassette in the wall or move along the wall, are equipped with a special type of handles without a protruding handle. They are embedded in the door leaf.

There are similar simple handles for cassette glass doors.

In addition, wooden sliding interior doors can have lockable handles.

Features of handles for interior glass doors

We have already mentioned two options for handles for glass doors. In addition to overhead and mortise, they also have knobs. For example, these:

If the glass door needs to be fixed or locked, then the latch and lock mechanism cannot be embedded into the door leaf. Therefore, for these cases, overhead models of handles are produced - with a latch:

or with a latch and lock.

Door handles are an additional obstacle between rooms. For doors, they play a rather important role during operation: without a handle, you can comfortably open the opening in only one direction. This article discusses the issues of what are door handles for interior doors, their device, materials for manufacturing.

To understand the mechanism and its purpose, it is necessary to consider the design of the product.

Their main types are presented in the table:

Type of handle Peculiarities

In such knobs, the latch is controlled by turning the handle, which may also have the shape of a ball or disk.

A variety of handles - products with push-button and rotary latch.

Lack of designs: not very convenient to use.

These are modern door handles for interior doors.

When the handle is pressed, the latch opens or closes, keeping the doors in the closed position.

Often they are made together with a lock or latch.

Stationary products are not responsible for the operation of the latch or lock (see).

These are pens, from long-outdated staples to modern counterparts, looking like a variety of balls, figures of various animals or colors.

Often they are used for ease of use of doors.

A separate subspecies - interior handles. Their feature is that they should not protrude beyond the door leaf.

These are mortise products that can have a latch control, a latch for it, an overlay with a slot for a key.

Its difference from the rest is in the form and type of installation.

Magnetic handles or locking mechanisms are gaining more and more popularity. The handle in the product only controls the device by pushing and pulling a large magnet resembling a lock. Such a mechanism may have a rotary or push handle.

Product design

The photo shows the main elements of the push handle.

The basic design consists of the following parts:

  • Latches. This is an internal mechanism that is designed to block the canvas in the opening. The main element of the knot is a crossbar - a latch, a latch tongue.
  • Cylinder mechanism. It is brought out, connected to the handle, and serves to move the inside of the structure.
  • handles. An element that is subjected to a force.
  • Decorative lining or socket. Disguises the fixation of the lock and gives the door a beautiful appearance.
  • Reply. Placed on a box. It is a plate that closes the hole in the frame, into which the latch tongue enters.

Materials for manufacturing

The door handle for interior doors does not require the use of such durable materials as for entrance doors. The load on it is not so big.

She may be:

  • Metal, from various alloys of brass, silumin. Such products are considered the most durable for interior doors. A disadvantage can be considered, for example, the fragility of silumin, which, with intensive use of doors, can lead to breakage of the handle.

  • Plastic. Disadvantages of the product: short service life, not too spectacular appearance. But it's a low price.

  • Wooden. Possesses natural beauty of materials. Such pens are pleasant to the touch, their cost is relatively small, but they do not differ in a wide variety of shapes.
  • Usually, the interior door handle made of wood is made round, it can be disc-shaped and sometimes in the form of a bracket, but in this case it is combined with metal elements.
  • The limitation of the diversity of their species is associated with the possibilities of processing wood on a lathe.

  • Glass. This is a beautiful and spectacular product, but the glass is very fragile - it breaks with careless handling, which limits their range. Most often, these are round handles or combined options with other types of materials as a variety of decorative inserts.

The most popular scheme for assembling a handle for an interior door is a combined one, made of different materials. For example: metal with glass, or metal with wood.

The main drawback of the design is fragility, due to the peculiarities of combining different materials into a whole product.

Criterias of choice

Tip: Everyone chooses the shape and design of the door handle, but you need to remember that the product must be combined with both the door itself and the general interior of the house.

The main criterion for choosing designs for interior doors is design.

In addition, evaluation factors may include:

  • Manufacturing quality. The product should not have loose connections, dangling or loose parts.
  • Ergonomics. The handle should be comfortable for the hand, pleasant to the touch and easy to use.
  • The combination of style with the interior of the premises. The handle should be of the same style and color as the door hinges and other fittings.
  • On all adjacent doors, the handles are selected completely the same.
  • Originality is not expressed in frivolity.

Tip: When purchasing door handles, it should be understood that this is only an addition to the doors, and not their main element.

Archie door handles

Door handles for archi interior doors are:

  • Great design.
  • A very good quality.
  • Durability.
  • Ergonomics.
  • Practicality.
  • Competitive cost.
  • Huge range of products.

For the manufacture of products, an alloy of zinc, aluminum, copper, magnesium (TsAM) is used, there are options from steel or brass.

Such products have seven main layers-coatings:

  • The first two layers are a copper coating applied to the base, which significantly increases the strength of all subsequent layers applied to the base.
  • The third layer serves to level the surface, the material is nickel. Before applying it, a final polishing is performed, which allows you to remove even very small irregularities.
  • The fourth layer is tinting, the product acquires the final shade under: gold, nickel, chrome, antique bronze or matte surfaces.
  • The fifth layer is a protective coating. It is used to protect the color and prevent it from fading due to time or external factors.
  • The last two layers are the latest developments, which are an electrophoretic coating that significantly enhances the protective properties of the product. The coating prevents the appearance of corrosion on the material, prevents the negative effects of the environment.

Before entering the distribution network, all brand products undergo a series of tests, which allows you to test their quality and eliminate defects.

No less popular are interior door handles manufactured by the French brand Leroy Merlin. Their difference is high quality at competitive prices.

Door handle installation

Do-it-yourself installation of any handle on an interior door begins with determining the height of the product above the floor level.

According to the standard, this is 80 - 90 centimeters, but with a deviation from the average height of a person, this size can change up or down.

The installation instructions for the product suggest the following workflow:

  • Markup. The selected height is marked on the side and on the end of the door leaf. In the center of the end, the place for drilling a hole for the entrance of the latch latch is indicated. On the side of the door leaf, the location of the hole is marked for installing the handle.
  • Drilling holes.
  • It is marked and made a sweat to fix the decorative latch strip.
  • The product is assembled inside the door leaf: the latch is inserted into the end hole and screwed with two self-tapping screws.

Tip: Before final installation, the hole should be blown well with air, which will prevent the latch from sticking from wood dust entering the device.

  • The square is set.
  • First, one handle is put on the square and screwed to the door leaf with screws.

  • The second handle is installed.
  • The functionality of the structure is checked.
  • Decorative caps are attached to hide the attachment points of the product.
  • The mating part of the latch crashes into the door frame.

The process of mounting the handle on an interior door with all the details shows the video in this article.

Without a handle, a door is not only an inconvenience during operation, but also its unfinished appearance as a whole. Door handles for interior doors are produced by many companies, which allows each person to purchase any product according to their taste and financial capabilities.

The handle for the front door should not only fulfill its function, but also complement the design of the door leaf. Since there are a large number of them on the market, the choice must be approached with great care.

The fittings for the front door differ in many factors:

  • operating principle;
  • appearance;
  • purpose;
  • material;
  • installation.

There are the following types of mechanisms:

  1. push-button;
  2. pressure;
  3. stationary;
  4. staples;
  5. on the plank.

Material

The following materials can be used in the manufacture:

  • iron;
  • tree;
  • glass;
  • aluminum;
  • brass;
  • stainless steel;
  • silumin;
  • TsAM (an alloy of zinc, aluminum and copper).

Most often, models made of wood, brass, TsAM or stainless steel are chosen for entrance doors. This is due to the strength of products, durability and high resistance to environmental influences. TsAM models are slightly less durable than brass devices. In everyday life, such a difference is almost imperceptible, and the price of the latter material is much higher.

To protect the handles for entrance doors from the effects of the external environment, to make the material stronger and improve its appearance, various coatings are applied to the fittings:

  1. polishing;
  2. brushing;
  3. oxidation;
  4. powder coating;
  5. polished chrome plating;
  6. matte chrome plating;
  7. gilding with varnish;
  8. anodizing;
  9. galvanizing;
  10. brass plating.

Popular are polishing, chrome plating and anodizing. Lacquer or paint should be avoided. Over time, this material cracks and falls off, which leads to corrosion of the metal.

Push-button, push and stationary

Push-button devices are a subspecies of lever handles. You can also come across such names as noba or knoba. They have a spherical handle. Since they do not have a lever, they open by turning the ball counterclockwise or clockwise. As a material for the manufacture of these fittings, brass is often used.


Products of this type are most often installed in interior doors. For entrance structures, ball-shaped handles without a latch are used. An exception may be the entrance doors to utility rooms.

Push devices have a latch latch that cuts into the door leaf. When you press the lever, it hides inside the structure, allowing you to gain access to the room. After the handle is returned to its original position, the latch retracts. Devices can be equipped with a lock or purchased separately from the locking block.

This model can be of 2 types:

  • with a solid overlay;
  • with separate pads.

The first type is used in conjunction with latch and deadbolt locks. When buying this type of device, consider:

  1. center distance between the center of the keyhole and the handle;
  2. lining width;
  3. keyhole shape;
  4. section of the profile pin for the handle.


When choosing a product with separate linings, there is no need to take into account the center distance. The handle can be installed separately from the locking mechanism.

Stationary products are not connected to the lock, they cannot be turned or pressed. They are designed to pull or push the door. The installation of such a handle is quite simple and consists in fixing it on the door leaf with self-tapping screws or tightening screws. These devices have a different appearance, but the most common are handle-brackets.

Since this product does not have a latch, experts recommend installing a separate roller mechanism. It will fix the door when the lock is open and prevent arbitrary swinging of the door leaf.

Pull handle

The handle-bracket is a common model of stationary products. It has a U-shape and is attached to a wooden or metal door. It does not have a deadbolt or latch. Their main advantage is considered to be the simplicity of design. This avoids wear on the latch or breakage of the lever due to excessive pressure. Another advantage is the different material of manufacture. It can be made independently from wood, decorated with carvings or patterns.


On the bar

This product is a kind of pressure structures. If the device is completed without a lock, then a handle on a bar with an external lining can be supplied. The mechanism and the locking block can be made by different manufacturers. The main condition will be compliance with a single design. Some handles have a turning mechanism on the inside that does not allow the door to be opened from the outside with a key. If the device is equipped with a lock, you need to pay attention to its class and quality.


Features of handles for metal doors

The following two types are most often used as a door handle on a metal front door:

  • stationary;
  • pressure.

Since a metal door is heavier than a wooden one, the handle must be sized for its weight. This is important to consider when choosing the material from which the handle is made and how it is attached. In most cases, products for wooden and metal door leaf are the same. They differ only in the way they are installed.

Principle of operation

All door handles work in the same way. So, knobs and mechanisms on the bar have a latch. The former hide the bolt inside the canvas when the handle is turned in a circle, and the latter set the latch in motion when the lever is pressed. Products without moving mechanisms work on the principle of "push-pull". Significant differences in the principles of operation are available only in locks.

DIY installation

Almost all front door handles can be installed independently. This requires some tools and basic skills in working with wood or metal.

You will need the following tools:

  1. pencil;
  2. ruler and tape measure;
  3. electric drill;
  4. self-tapping screws or coupling bolts;
  5. screwdriver or wrench;
  6. drills of the required diameter.

Height selection

The standard height of the product is 100-105 cm from the floor. If the owners are tall or short, you can install the mechanism at any other height. Convenient is the position of the handle, in which it does not interfere with opening the lock with a key. Most often this is the level of the belt or a little higher.

Mounting the mechanism with a lock

At the plastic front door, you can only replace the handle. Installing it yourself is quite difficult, without special knowledge and skills. Otherwise, the glass unit may be damaged.

To install a door handle with a lock in a wooden door, you must:

  • Mark the position of the lock on the door leaf. Do this from the end of the door, where the locking mechanism will be placed. It must be strictly centered. Also mark the holes for the handle and the larva. Sometimes a special template is used.
  • With a drill of the appropriate diameter, a hole is drilled from the end, which should match in size with the height of the lock. The depth is equal to the width of the locking mechanism. To do this, put a marker on the drill and make holes as close to each other as possible. The drill must be held perpendicular to the door leaf and the floor.
  • The edges are trimmed with a chisel and the groove is shaped. Sandpaper clean all places.
  • Drills of the required diameter make holes for the lock cylinder and the handle.
  • The lock should fit snugly into the recess. A faceplate is applied to it and fixed with screws or nails. If necessary, deepen the notch with a chisel so that the plate is flush with the end.
  • Installation of the handle and larvae. To do this, install a square pin and screw the lining.
  • Mount the back plate. To do this, a 5-7 mm deepening is made with a chisel in the loot, and a plate is placed on top. Attach it to small nails.

Replacing latch devices

To replace door devices with a latch, it is necessary to select the appropriate mechanism. The main condition is the coincidence of the cross section of the square of the handles. The rod may be slightly larger, but not smaller, because the device must be balanced and firmly fixed.


To dismantle the mechanism, unscrew the screws of the front plate, which presses the latch. Then remove the strips from the inner and outer handles, unscrew the clamping screw. Remove the square and pull out the latch handle, install a replacement by following these steps in reverse order.

Installation in sliding doors

For sliding doors, the device consists of two parts:

  1. pressure product;


The first part is mounted according to the same principle as the product with a latch. To install a mortise device, you must:

  • Mark with a pencil on the second half of the door its position and dimensions.
  • A hole is drilled along the edges with a pen to a depth of 12-14 mm. Make additional indentations from top to bottom.
  • With a chisel, the groove is given the necessary shape. This can be done with a hand saw.
  • Insert the insert and fix it with screws on both sides.

Installing Stationary Views

Installation of stationary products is quite simple. To do this, mark the position of the device on the door leaf, attach the bar to the mark and fix it with self-tapping screws. If screws are used for fastening, make through holes in the places of their installation. Then thread the screws on one side of the handle, insert them into the holes, apply the second product and fix it tightly.


Repair manual

The sticking handle should be lubricated with oil or other special liquid. The cause of the breakdown may be the ingress of dust or dirt between the moving mechanisms. If the handle falls off, you need to remove the retaining ring. In most cases, it is bent or broken. Then it is necessary to replace it, since the old one is no longer serviceable. If the four-sided clamping screw breaks, the entire mechanism must be changed.

Door hardware of any kind can be repaired, and repair recommendations are easy to follow on your own.

TYPES OF HANDLE FOR INTERIOR DOORS BY CONSTRUCTION TYPE

Stationary handles
Usually they have a U-shape (the so-called handle-brackets), less often - round or tulip-shaped. Completely independent of the lock or latch and operate on a "pull" (or "push" if the door opens inward) principle.

Stationary pull handles

Round stationary handles

There is no mechanism, which means there is nothing to jam and loosen up.
+ Withstand a significant load, suitable for massive doors.
+ Inexpensive: you can meet even 100 rubles.
+ Elementary installation.
+ A huge selection of materials - from wood to stainless steel.
– Old-fashioned or overly utilitarian design.
- You can’t put a familiar (flange) latch to them, except perhaps a primitive roller one.
– Require more force when opening/closing the door.

If you settled on the option with a bracket, then choose a handle with an eye on the mass of the door leaf. The heavier it is, the larger and more massive the bracket should be.


Handles on rosette (flange)

Usually the socket is round. but also square.


Stylish and functional pressure models. If you were in doubt about which handle to choose for an interior or office door, then take this one. A big plus of the handle on the socket is that it is attached through a standard 8 mm square, so you can easily match the latch and latch to it, which will allow you to tightly close and lock the door.

An elegant and modern solution that looks neat on any door.
+ You can install any latch - even magnetic, even mechanical.
+ Add a latch or latch-key to the handle and latch - and the door can be locked.
+ Very convenient, do not require effort when opening.
- Several times more expensive than stationary ones.

You can choose an excellent handle on a socket for interior or office doors at.


Handles on the bar

Handle on the bar with a slot for the lock


The same lever handle, but assembled with a bar (solid overlay). On the bar there can be a turntable for a lock, a slot for a cylinder mechanism or a lever key (option for the front door). However, there are models on a deaf bar.

Combined solution.
+ The cost is comparable to the handles on the outlet.
+ Look stylish in classic interiors, especially in spacious rooms.
- Restricted in the choice of castle.
- They take up a lot of space on the canvas.
- Any inconsistency with the interior will be evident.
- In general, they look much better in the office or on the front door than inside the house.

The question of how to choose a handle for an interior door requires a strategic approach. Consider in advance whether the door should be locked, and if so, how. If over time you want to put a lock or change the mechanism (for example, from a eurocylinder to a lever), and there is no suitable hole on the bar, the handle will have to be changed.

In addition, if you take the handle on the bar with a keyhole, do not forget to make sure that the center distances of the handle and the lock match.
Prices - from 734 rubles.


Knobs

Handle-knob: economical and short-lived

Combined handles with a latch or lock - albeit a ready-made, but not such a reliable solution. We did not begin to paint their qualities - the rare advantages and numerous disadvantages of knobs are sorted out in.


PEN MATERIALS: COMPARE THE FIVE MOST POPULAR

Aluminum door handles: economy option



Aluminum handles are the best choice for inexpensive doors
These handles captivate with their availability: they are inexpensive and are sold in any hardware store. Please note: they are very light. Accordingly, if you have a massive door or you like to feel the pleasant heaviness of metal in your hand, it is better to choose a handle from another popular material - TsAM.

Advantages of aluminum handles
1.5-2 times cheaper than TsAM handles.
Suitable for plastic, "Finnish" and other lightweight interior doors.
Do not rust, can be installed in the kitchen or in the bathroom.

Cons of aluminum handles
Designed for a moderate load, on heavy canvases they bend and break faster.
Feels cool and slippery.
After 1-2 years, they begin to peel off, exposing their true silver-white color.
Easily scratched. Be careful if you wear a ring or ring.


Door handles from TsAM: balance "price - quality"

TsAM - the most popular material for the manufacture of door handles

TsAM (ZAMAK, “tsamak”) is a zinc alloy with aluminum, copper and magnesium as alloying components. This material is good, balanced in everything. And if you are looking for something as eternal as brass, but are not psychologically ready to pay more than 2,000 rubles for an interior door handle, then the best choice is a zinc alloy model.

Advantages of ZAMAK handles
2-3 times cheaper than brass handles, but almost as strong as them.
Not afraid of corrosion - can be put on the door to the bathroom or kitchen.
Practically do not wear out, retain their presentation for years.
Perfect adhesion to electroplating guarantees an even and juicy shade.

There are no noticeable shortcomings, but the characteristics may float depending on the composition of the material. So, the more% copper it contains, the stronger and more expensive the handle. Much depends on the origin of the alloy - whether it is obtained from "pure" ore raw materials or processed from scrap and contains impurities of cadmium, lead and tin. All Palladium pens from TsAM are Grade A.


Brass door handles: expensive pleasure



Brass has a pleasant golden color, products from it age nobly

Not every company will undertake the conveyor production of brass handles, not every buyer will allow himself to buy them. It's a pity, because in everything else, except for the exorbitant price, they are simply wonderful.

Advantages of brass handles
Strong and durable.
Do not rust throughout the entire service life.
They endure weather hardships and therefore are suitable for entrance doors.
Pleasant and warm to the touch.
Unlike other pens, they age gracefully.
Brass has an antimicrobial effect.

Cons of brass handles
Expensive. Instead of one brass handle, you can buy two of TsAM or three of aluminum.
A niche product that is increasingly difficult to find in retail.

Price per site: presented in the collection


Stainless steel door handles: an office in your home


Stainless steel handles are strong, durable, but often with a primitive design.

Yes, stainless steel is strong. Yes, it is durable. But it is difficult to make something elegant out of it: it is too reluctant to process. It remains only to pour something simple - like handles, staples or the simplest forms. It is acceptable for office doors, but how to fit such a miracle into the house is completely incomprehensible. Although, the taste and color ...

Advantages of stainless steel handles
Stronger and more durable does not happen.
Suitable not only for interior doors, but also for entrance doors.
Can be placed in the kitchen, bathroom and other areas with high humidity.
It takes a lot of effort to scratch the coating.

Cons of stainless steel handles
Unsightly design: most of the steel handles are stationary brackets.
Cold to the touch.

Site price: not presented


Plastic door handles: cheap but not cheerful


Plastic handles - the antipode of the word "reliability"
A completely justified choice for light PVC doors or high-tech interiors, but at least controversial in all other cases.

Pros of plastic handles
Cheaper than metal handles.
Any color is possible - even matte white, even glossy carrot.
Amazed by the variety of shapes and designs.
Not afraid of wet hands - suitable for doors to the bathroom or kitchen.
Pleasant to the touch, do not slip in the hand.

Cons of plastic handles
Flimsy, even on light doors they live on strength for several years.
They scratch with a fingernail and collect fingerprints.
Models "under the metal" bear little resemblance to the material they imitate.
On a solid wooden door, they look like a toy and third-rate.

Website price: – (soon on sale, stay tuned)


TIPS ON HOW TO CHOOSE THE RIGHT HANDLE FOR INTERIOR DOOR

1. Match the color of the door handle with the lock, escutcheon and hinges.

2. Try to pick it up so that it does not discord with furniture and accessories. Bronze railing will not tolerate matte chrome handles.

3. Cold shades are usually suitable for modern, high-tech, loft styles; warm - for classic interiors.

4. On canvases with a wenge or bleached oak finish, handles in shades of chrome, palladium and those close to them look great. Handles of golden hues suggest themselves to the walnut and cherry doors: in fact, gold and brass.

5. The type of door handle is a matter of taste. But in general, push (lever) models are more reliable than round ones, and not as slippery to the touch.

6. Let the shape of the product echo the design of the canvas. The easiest way to focus on the panels. For example, on a canvas with two rectangular panels, a bizarrely curved handle is clearly out of place, it is better to choose a straight one.

7. For doors to adjacent rooms, select the same handles.

8. If you decide to take a knob, keep in mind that it has a non-standard mounting hole: more than 5 cm. Because of this, you will not be able to replace the knob with separate fittings in the future.

9. If you have a sliding door, you need a special type of handles - "boats". Read more about them in our article on fittings for sliding doors.


Looking for a beautiful and durable door handle with up to 12 years warranty? Look into .



No tags


From the article you will learn:

A door that does not have a handle cannot be called comfortable and fully functional. The choice of a door handle should be given special attention, because the parameters of this small product determine how comfortable the use of the door structure will be.

To freely and easily open in any direction, you need to know what door handles are, what advantages each model has and how to install it yourself.

Types of handles in interior doors

Handles designed for interior structures are practically no different from models produced for installation in entrance doors. All these products have an identical design scheme and features. And only a few small nuances are worth noting separately.

First of all, we are talking about the material from which they are made, and secondly, there are slight differences in the mechanism and principle of operation.

Varieties of interior door handles:

  • Stationary Models. They do not provide interaction with the locking mechanism or latch. This type includes a whole mass of products, starting with staples that were widely used a century ago. An impressive list is completed by modern analogues of such products, produced in the form of figures of animals and people, balls, spheres and their geometric varieties. The main task of such a model is to ensure the convenience of using the door structure.
  • pressure. Modern modification, equipped with a latch. Pressing the handle causes the latch to move in the desired direction. The latch holds the door securely closed. This model is widespread and equally often installed on interior and entrance structures. Often, manufacturers implement this option in conjunction with a locking mechanism. Two subspecies of the product are produced - handles with a base in the form of a heel, in which point fastening is provided, and models equipped with an oblong bar designed to locate the keyhole.
  • Rotary knobs, often referred to as knobs. The principle of operation of this model is identical to the mechanical manipulations that make the handle-locks installed on interior doors work. In this case, the difference lies only in the features of the mechanical load. The latch is not driven by pressure, but by turning the handle. Usually these models are produced in the form of a ball, sphere or disk. Varieties are distinguished in the general group - samples equipped with a push-button or rotary latch position lock. Users do not always note the ease of use of both modifications.
  • Handles designed for sliding doors. The main distinguishing feature of this model is certain geometric parameters, due to which its elements do not extend beyond the borders of the door leaf. In this case, there is a clear resemblance to mortise products. Functions, subtypes and technical solutions resemble similar characteristics of other door handles. Manufacturers produce varieties equipped with a latch with a locking function, with an overlay on which there is a slot in the form of a keyhole, with different options for the opening mechanism. Basically, all the differences between come down to the difference in geometric shape and to the installation features.
  • Magnetic. One of the latest developments, which no longer resembles a handle, but a direct locking mechanism. The handle in this model serves to control a powerful magnet, which, moving in the right direction, securely fixes the door leaf in a given position. The device equally often uses handles with a rotary and push operating principle.

This is the main classification under which all existing types of door handles for interior structures fall. Some manufacturers equip their products with additional parts and functions. However, in fact, any of them can be attributed to one of the above types. For example, a number of manufacturing companies distinguish such a variety as handles for installation on metal-plastic doors. But, in fact, these models are ordinary pressure modifications.

Entrance door handles are predominantly made from strong, durable materials such as stainless steel. In contrast, models designed for interior structures are made from various types of raw materials. The "home" options are not subject to such stringent requirements as their "street counterparts", which are often operated in harsh weather conditions.

Therefore, manufacturers are practically unlimited in the choice of materials for the manufacture of interior door handles. The most common on the shelves are metal, plastic, wooden, glass, combined models. Here, the original, presentable design often comes first, as opposed to strength, durability and reliability.

The main types of door handles are as follows:

  • metal. For the manufacture of such products, various alloys are used, including brass, TsAM (aluminum, copper and zinc), silumin, etc. The mechanical load on the handles that are installed on interior door structures is minimal, and therefore such materials are ideal for the manufacture of door handles. Products made from such raw materials, in terms of their strength characteristics, are an order of magnitude ahead of all other models. However, it is worth noting that each material used has its drawbacks. For example, silumin has increased fragility. With intensive use, handles made from it break quite quickly.
  • Plastic. This is a budget option that cannot boast of outstanding technical characteristics or external data. The main advantage of plastic models of handles is their low cost. Therefore, they still find their consumers, despite the short service life and dubious aesthetic properties.
  • Wooden. Natural, natural materials have an outstanding aesthetic appeal and good technical performance. Wooden models of door handles are pleasant with tactile contact, they retain heat well and are in the price range affordable for many consumers. Among the shortcomings of the modification, it is worth noting the insufficient variety of forms. The number of types is limited by the capabilities of lathes. Usually such models are balls, discs or staples. In the latter case, we are talking about a combination of wood with metal parts.
  • glass. The material captivates with its appearance. As a rule, glass handles look very impressive. One of the main drawbacks is fragility. If the handle is handled carelessly, it breaks easily. To increase the strength of the product, manufacturers prefer to combine glass with other materials. Often it is presented in a certain model only as decorative inserts that do not take on the main mechanical load.

Among the most popular options are combined handles designed for. Popular combinations are metal and glass, metal and wood. Such structures also have a significant drawback. They are short-lived due to the lack of effective technologies that would provide a reliable connection of individual elements from different materials into an integral product.

Choosing handles for interior doors

When choosing the right model, there are several important parameters to consider. If we make a comparison with the handles for the entrance doors, then the main role is played not by strength, but by design.

The main selection options are as follows:

  • Execution quality. When buying a product, it is necessary to test it for the strength of the connections between the individual elements. A well-made handle has no room for loose or loose parts.
  • Ergonomics. If the model is designed taking into account the physiological characteristics of the human hand, then it is convenient to use. Ergonomically designed products easily and naturally “fit” in the hand, they are pleasant to the touch and do not cause discomfort during operation.
  • Compatibility with the chosen interior style. When choosing a suitable model, it is necessary to pay attention to the style in which it is “aged”, its color and shape. It is important to observe the norms of harmonious unity of the handle with the door leaf, awnings and other fittings.
  • Identity with other similar products used indoors. For all rooms of the same house or apartment, you should buy the same door handles. For this reason, it is better to immediately purchase the right amount of pens, because even in different batches of products of the same article there may be slight differences in appearance (as a rule, there is a slightly different shade).

It is important to remember that the purpose of the handle, first of all, comes down to the main task - to ensure maximum convenience in opening and closing the door. For the buyer, the main rule is to find the “golden mean” between the functional features of the model and its external data.